Konfigurasi Routing RIPv2 Menggunakan Cisco Packet Tracer
Konfigurasi Routing RIPv2 Menggunakan
Cisco Packet Tracer
Writer Dia Putera
Skenario : Perusahaan X ingin membangun sebuah jaringan dimana perusahaan tersebut menggunakan routing RIPv2 pada topologi jaringan mereka,ditribusi IP telah ditentukan oleh NA(Network Administrator)sehingga NE(Network Engineer)tinggal melakukan konfigurasi yang diminta.
Alokasi IP Address
| Daftar IP Address | ||
| Nama | Port | IP Address |
| Data Center | G1/0 | 192.168.10.1/24 |
| G2/0 | 192.168.20.1/24 | |
| G3/0 | 192.168.30.1/24 | |
| G4/0 | 192.168.40.1/24 | |
| G5/0 | 192.168.50.1/24 | |
| Data A | G0/0 | 192.168.10.2/24 |
| G0/1 | 10.10.10.1/24 | |
| Data B | 192.168.20.2/24 | |
| G0/1 | 11.11.11.1/24 | |
| Data C | G0/0 | 192.168.30.2/24 |
| G0/1 | 12.12.12.1/24 | |
| Data D | G0/0 | 192.168.40.2/24 |
| G0/1 | 13.13.13.1/24 | |
| Data E | G0/0 | 192.168.50.2/24 |
| PC 1 | F0/0 | 10.10.10.5/24 |
| PC 2 | F0/0 | 11.11.11.5/24 |
| PC 3 | F0/0 | 12.12.12.5/24 |
| PC 4 | F0/0 | 13.13.13.5/24 |
Gambar Topologi
Konfigurasi DATA-CENTER
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hos
Router(config)#hostname Data-Center
Data-Center(config)#
Data-Center con0 is now available
Press RETURN to get started.
Data-Center>en
Data-Center#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Data-Center(config)#int g1/0
Data-Center(config-if)#ip ad
Data-Center(config-if)#ip address 192.168.10.1 255.255.255.0
Data-Center(config-if)#no sh
Data-Center(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet1/0, changed state to up
Data-Center(config-if)#int g2/0
Data-Center(config-if)#ip ad
Data-Center(config-if)#ip address 192.168.20.1 255.255.255.0
Data-Center(config-if)#no sh
Data-Center(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet2/0, changed state to up
Data-Center(config-if)#int g3/0
Data-Center(config-if)#ip ad
Data-Center(config-if)#ip address 192.168.30.1 255.255.255.0
Data-Center(config-if)#no sh
Data-Center(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet3/0, changed state to up
Data-Center(config-if)#int g4/0
Data-Center(config-if)#ip ad
Data-Center(config-if)#ip address 192.168.40.1 255.255.255.0
Data-Center(config-if)#no sh
Data-Center(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet4/0, changed state to up
i
% Ambiguous command: "i"
Data-Center(config)#int g5/0
Data-Center(config-if)# ip ad
Data-Center(config-if)# ip address 192.168.50.1 255.255.255.0
Data-Center(config-if)#no sh
Data-Center(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet5/0, changed state to up
Data-Center(config-if)#ex
Data-Center(config)#rio
Data-Center(config)#ro
Data-Center(config)#router rip
Data-Center(config)#router rip
Data-Center(config-router)#ver
Data-Center(config-router)#version 2
Data-Center(config-router)#no au
Data-Center(config-router)#no auto-summary
Data-Center(config-router)#net
Data-Center(config-router)#network 192.168.10.0
Data-Center(config-router)#net
Data-Center(config-router)#network 192.168.20.0
Data-Center(config-router)#net
Data-Center(config-router)#network 192.168.30.0
Data-Center(config-router)#net
Data-Center(config-router)#network 192.168.40.0
Data-Center(config-router)#net
Data-Center(config-router)#network 192.168.50.0
Data-Center(config-router)#ex
Data-Center(config)#
Konfigurasi DATA-A
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#Dhos
Router(config)#hos
Router(config)#hostname Data-A
Data-A(config)#ip ad
Data-A(config)#int g0/0
Data-A(config-if)#ip ad
Data-A(config-if)#ip address 192.168.10.2 255.255.255.0\
^
% Invalid input detected at '^' marker.
Data-A(config-if)#
Data-A(config-if)#ip address 192.168.10.2 255.255.255.0
Data-A(config-if)#no sh
Data-A(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Data-A(config-if)#int g0/1
Data-A(config-if)#ip ad
Data-A(config-if)#ip address 10.10.10.1 255.255.255.0
Data-A(config-if)#no sh
Data-A(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Data-A(config-if)#ex
Data-A(config)#rou
Data-A(config)#router rip
Data-A(config)#router rip
Data-A(config-router)#ver
Data-A(config-router)#version 2
Data-A(config-router)#no au
Data-A(config-router)#no auto-summary
Data-A(config-router)#net
Data-A(config-router)#network 192.168.10.0
Data-A(config-router)#net
Data-A(config-router)#network 10.10.10.0
Data-A(config-router)#ex
Data-A(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet 0/0
%Default route without gateway, if not a point-to-point interface, may impact performance
Konfigurasi DATA-B
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ho
Router(config)#hostname Data-B
Data-B(config)#int g0/0
Data-B(config-if)#ip ad
Data-B(config-if)#ip address 192.168.20.2 255.255.255.0
Data-B(config-if)#no sh
Data-B(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Data-B(config-if)#int g0/1
Data-B(config-if)#ip ad
Data-B(config-if)#ip address 11.11.11.1 255.255.255.0
Data-B(config-if)#no sh
Data-B(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Data-B(config-if)#ex
Data-B(config)#rou
Data-B(config)#router rip
Data-B(config)#router rip
Data-B(config-router)#ver
Data-B(config-router)#version 2
Data-B(config-router)#no au
Data-B(config-router)#no auto-summary
Data-B(config-router)#net
Data-B(config-router)#network 192.168.20.0
Data-B(config-router)#ne
Data-B(config-router)#network 11.11.11.0
Data-B(config-router)#end
Data-B#
Konfigurasi DATA-C
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hs
Router(config)#hos
Router(config)#hostname Data-C
Data-C(config)#int g0/0
Data-C(config-if)#ip ad
Data-C(config-if)#ip address 192.168.30.2 255.255.255.0
Data-C(config-if)#no sh
Data-C(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Data-C(config-if)#int g0/1
Data-C(config-if)#ip ad
Data-C(config-if)#ip address 12.12.12.1 255.255.255.0
Data-C(config-if)#no sh
Data-C(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Data-C(config-if)#ex
Data-C(config)#rou
Data-C(config)#router ri
Data-C(config)#router rip
Data-C(config-router)#ver
Data-C(config-router)#version 2
Data-C(config-router)#no au
Data-C(config-router)#no auto-summary
Data-C(config-router)#net
Data-C(config-router)#network 192.168.30.0
Data-C(config-router)#net
Data-C(config-router)#network 12.12.12.0
Data-C(config-router)#end
Data-C#
Konfigurasi Data-D
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hos
Router(config)#hostname Data-D
Data-D(config)#int g0/0
Data-D(config-if)#ip ad
Data-D(config-if)#ip address 192.168.40.2 255.255.255.0
Data-D(config-if)#no sh
Data-D(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Data-D(config-if)#int g0/1
Data-D(config-if)#ip ad
Data-D(config-if)#ip address 13.13.13.1 255.255.255.0
Data-D(config-if)#no sh
Data-D(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Data-D(config-if)#ex
Data-D(config)#rou
Data-D(config)#router
Data-D(config)#router i
Data-D(config)#router ri
Data-D(config)#router rip
Data-D(config-router)#ver
Data-D(config-router)#version 2
Data-D(config-router)#no au
Data-D(config-router)#no auto-summary
Data-D(config-router)#net
Data-D(config-router)#network 192.168.40.0
Data-D(config-router)#net
Data-D(config-router)#network 13.13.13.0
Data-D(config-router)#ex
Data-D(config)#end
Data-D#
Konfigurasi Data - E
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ip
Router(config)#int g0/0
Router(config-if)#ip ad
Router(config-if)#ip address 192.168.50.2 255.255.255.0
Router(config-if)#no sh
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Router(config-if)#int g0/1
Router(config-if)#ip ad
Router(config-if)#ip address 14.14.14.1 255.255.255.0
Router(config-if)#no sh
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Router(config-if)#ex
Router(config)#rou
Router(config)#router r
Router(config)#router rip
Router(config-router)#ver
Router(config-router)#version 2
Router(config-router)#no au
Router(config-router)#no auto-summary
Router(config-router)#net
Router(config-router)#network 14.14.14.0
Router(config-router)#net
Router(config-router)#network 192.168.50.0
Router(config-router)#end
Router#
Routing Information Protocol
Routing Information Protocol atau bisa disingkat RIP merupakan salah satu routing yang open standard artinya dapat diterapkan pada beberapa router.RIP memilik batasan hops network untuk mengurangi beban kinerja bandwidth karena setiap 30 detik RIP akan melakukan pembaharuan network untuk mengidefikasi(mengenali)apakah ada network baru yang terhubung atau tidak.
Kenggulan RIPv2
- Ini adalah protokol standar.
- Ini sesuai dengan VLSM.
- Ini mengirimkan pembaruan yang dipicu ketika jaringan berubah
Kelemahan RIPv2
- Maksimal jumlah hop 15
- Pembaharuan jaringan setiap 30 detik,dapat menyebabkan pembengkakan penggunaan bandwidth
Download link pkt files : https://forum.seccodeid.com/archives
Ini buat topolgy jaringan?